Fasteners General Categories
- from Small Parts and Bearings

Latches - Panel Fastener - Butt Joint

Search Rating: 58%

Progressively draws panels together. Helps provide airtight or water tight seal. Adjustability for manufacturing tolerances and gasket shrinkages. Receptacle needs to be purchased separately.

Uses 8mm hex to actuate. Bright chromate dipped, zinc plated carbon steel. Ultimate tensile load 625kg. Ultimate shear load 890kg.

Snap Buttons - Double End

Search Rating: 56%

Also see combined categories:
All Snap Buttons

Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.

Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.

Snap Buttons - Flat Type

Search Rating: 56%

Also see combined categories:
All Snap Buttons

Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.

Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.

Latches - Pawl - Quarter Turn

Search Rating: 56%

An ideal fastener for gasketed doors and access panels subject to wide thickness or misalignment tolerances.

Grip length is variable from 3.2mm to 36.5mm and is set by rotating the centre spindle. Latch can be opened with a quarter turn of the outer ring. Steel with black plastic outer ring. Installation hole diameter 19.43mm. Instructions included. Panel thickness from 1.2 to 3.2mm max. The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.

Pins - Groove

Search Rating: 56%

Also see combined categories:
All Groove Pins

Non threaded press fit fastener that doesn't require a reamed hole as do dowel pins.Commonly used in place of taper pins.

An economic method of fastening without the need for precision drilled and reamed holes. Recommended hole tolerance is H11. Total length may be slightly longer than the nominal length. Expanded portion of the pin is compressed into the hole a few thousands of an inch wider than the nominal pin diameter. Radial forces lock the pin securely into the drilled hole.

Snap Buttons - Single End - Dog Leg

Search Rating: 56%

Also see combined categories:
All Snap Buttons

Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.

Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.

Snap Buttons - Single End - Spring Leg

Search Rating: 56%

Also see combined categories:
All Snap Buttons

Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.

Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.

Mounts - Cylindrical - Square

Search Rating: 53%

Also see combined categories:
All Cylindrical Mounts

Rubber hardness 60 Duro Standard unless otherwise noted. Vibration dampening

Fastener may be steel, brass or zinc plated. Natural Rubber isolator.

Screws - Pan Head - Aluminium

Search Rating: 52%

Also see combined categories:
All Machine Screws

UNC metal thread machine screws

Nuts sold separately - See Fasteners - Nuts.

General Derailer Sprocket Parts

Search Rating: 52%

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

Switches - General

Search Rating: 51%

Also see combined categories:
All Switches

Lubricants - General

Search Rating: 51%

Various brands and types. Includes Inox, Lanox, Anti-Seize, Cutting Fluid, Chain Lube, Moly Lube, Food Grade Grease, PTFE Lubes, Silicone and more

Some items in this category are marked as only available for collection. Includes high temperature and food grade lubes. Battery Conditioner - Oils - Moisture Inhibitor - WD - Valve and Oring Lubricant.

Tools - General

Search Rating: 51%

Also see combined categories:
All Tools

Butane Torch, Inspection Mirror, Mini Sandblaster, Nibbling Tool, Plastic Scriber, Pick Up Tool Set, Hex Driver Handle for Insert Bits

X-Acto Knife Sets - Pin Vises - Screw Pitch Gauges and more.

Castors - Plate - General Purpose - Fixed

Search Rating: 51%

Also see combined categories:
All Plate Type Castors

Castors - Plate - General Purpose - Swivel

Search Rating: 51%

Also see combined categories:
All Plate Type Castors

Castors - Plate - General Purpose - Swivel with Brake

Search Rating: 51%

Also see combined categories:
All Plate Type Castors

Wheels - Hobby - General

Search Rating: 51%

Also see combined categories:
All Wheels

Includes wheels for robots and general hobby applications

Also see tracks for Robotic applications.

Rod - Drill - General

Search Rating: 51%

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Chrome vanadium alloy with unfinished ends. Requires heat treating to harden. Small diameters may not be perfectly straight. Heat treating by air, water or oil.

Heatshrink

Search Rating: 51%

Includes Dubro Range.

Castors - Stud - Threaded - General Purpose - Swivel

Search Rating: 50%

Also see combined categories:
All Stud Type Castors

Games - Board

Search Rating: 50%

Also see combined categories:
All Games and Gadgets

Gravity Trap, Squatter and Design Your Own Board Game.

Games - Children

Search Rating: 50%

Also see combined categories:
All Games and Gadgets

Batik, bendomino, bingory, catz ratz and batz, chekov, chicky boom, coocoo, cosmic cows, dominoes, froggy boogie.

Quality wooden games and more. Goblett Gobblers - Design Your Own Board Game - Pengoloo. Kangaroos and Koalas - Quack - Quoridor - Speedy Eddie. Katamino - Splash Attack - Sputnik - Think Twice. Magic Pen - Zimbbos - Zippy Dice.

Games - Educational

Search Rating: 50%

Also see combined categories:
All Games and Gadgets

Crystals, science kits, space race and more

Katamino - Splash Attack - Sputnik - Think Twice. Magic Pen - Zimbbos - Zippy Dice.

Games - Magnetic

Search Rating: 50%

Also see combined categories:
All Games and Gadgets

Magnetic games

Games - Memory

Search Rating: 50%

Also see combined categories:
All Games and Gadgets

Brainbox Around The World, Maths and Nature. Memory Cards.

Games - Strategy

Search Rating: 50%

Also see combined categories:
All Games and Gadgets

Strategy Games including Wooden and other games. Ideal gifts for thinking people.

Gobblet on the Go - Ringgz - Double Shutter - Eye of Horus - Khet - Tower of Kadesh - Giza - Dividends. Jumping Java - Logan Stones - Hive - Army of Frogs - Quarto - Quixo - Quoridor - Batik - Pylos. Skybridge - Inside - Eclipse - Gipf - Zertz - Dvonn - Yinsh - Punct - Tamsk - Abalone - Pentago - Columns. Trinidad - Fire and Ice - Cityscape - Poison Pot - Zaroc - Megalith - Tantrix - Yikers.

Servo Motor - Hobby - General

Search Rating: 50%

Also see combined categories:
All Hobby Servo Motors

For cars, planes, boats and helicopters. JR, Spektrum, Futaba and Hitec

Gear Strength: Using nylon as a base, Karbonite gears are 4x the strength, Metal gears 16x and Titanium Alloy 48x.

Posts - Spring

Search Rating: 50%

Tools - Sets

Search Rating: 50%

Also see combined categories:
All Tools

General tool sets, screwdriver sets, tap sets, dies sets, hex key sets.

Tools - Drills

Search Rating: 50%

Also see combined categories:
All Tools

Hobby drill for very small bits.

Tools - Dubro

Search Rating: 50%

Also see combined categories:
All Tools

Dubro Range of Tools

Tools - Paint

Search Rating: 50%

Also see combined categories:
All Tools

Includes airbrush, compressor, brushes, paint stand and alligator clips.

Tools - Pliers

Search Rating: 50%

Also see combined categories:
All Tools

Pliers, multi tool.

Lengths shown are based on standard stock but may vary.

Tools - Punches

Search Rating: 50%

Also see combined categories:
All Tools

Number punch and letter punch sets

Lengths shown are based on standard stock but may vary.

Tools - Tweezers

Search Rating: 50%

Also see combined categories:
All Tools

Selection of tweezers for those fiddly jobs.

Tools - Wrenches

Search Rating: 50%

Also see combined categories:
All Tools

Lengths shown are based on standard stock but may vary.

Castors - Stud - Friction Ring - General Purpose - Swivel

Search Rating: 50%

Also see combined categories:
All Stud Type Castors

Pins - Hitch - External

Search Rating: 50%

Also see combined categories:
All External Hitch Pins

Similar to R-Clips, but designed for both arms to fit around a shaft groove rather thand having one arm through a bored hole.

Pins - Hydraulic Cylinder

Search Rating: 50%

Also see combined categories:
All Hydraulic Cylinder Pins

Games - Mind Challenge

Search Rating: 50%

Also see combined categories:
All Games and Gadgets

Strategy and skill games - great gift ideas

Great games of strategy and skill including KogWorkS. Mind Challenge Classic - Pyramid, Link, Ladies, Why, Sanity, Ei8ht, Tease, Square Off and Integr8. Challenging games to enhance memory, creativity and logical deductive reasoning. Simple rules. Easy to learn. Hours of fun.

Hobby - Washer Packs

Search Rating: 50%

Hobby Washer Packs. Includes Dubro Range

Channel - Brass

Search Rating: 50%

For general hobby applications.

Rod - Drill Blanks

Search Rating: 50%

Also see combined categories:
All Silver Steel Drill Blanks
All Drill Rod

Made of hardened high speed steel.

Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc.

Tools - Chain Breaker

Search Rating: 50%

Also see combined categories:
All Tools

Used to break roller chain at the pins

Tools - Gift Ideas

Search Rating: 50%

Includes Stylus, Magnetic Finder, Multitool, Laser Pointers

Tools - Nut Drivers

Search Rating: 50%

Also see combined categories:
All Tools

Includes socket wrench for 0-80 size screws

Lengths shown are based on standard stock but may vary.

Tools - Pin Vises

Search Rating: 50%

Also see combined categories:
All Tools

Lengths shown are based on standard stock but may vary.

Mounts - Vibration - Isolation Pads - General Purpose

Search Rating: 50%

Also see combined categories:
All Isolation Pad Mounts

For installation of industrial machinery where the ratio of shear loads to vertical loads is less than or equal to 1 to 5.

Base is unthreaded. The stud rests on the pad and is not threaded in or fastened to the pad. Self aligning feature compensates for uneven floors without sacrificing stability. Scientifically designed diamond suction cells of the neoprene insert firmly anchor the machine to the floor. Recommended for a wide range of industrial machinery and equipment where simple precise leveling is required. 25.4mm level adjustment.

Pins - Clik - Carbon Steel

Search Rating: 50%

Also see combined categories:
All Clik Lynch Pins

Self locking ring snaps down to hold them securely in place. Easy grip ring for quick removal. Also known as a lynch pin.

Pin is made from carbon steel and heat treated to RA 50-60. Ring is hot drawn spring steel with hardness of RC 47-48. Zinc plated.

Pins - Clik - Mild Steel

Search Rating: 50%

Also see combined categories:
All Clik Lynch Pins

Self locking ring snaps down to hold them securely in place. Easy grip ring for quick removal. Also known as a lynch pin.

Pin is made from carbon steel and heat treated to RA 50-60. Ring is hot drawn spring steel with hardness of RC 47-48. Zinc plated.

Games - Card and Dice

Search Rating: 50%

Also see combined categories:
All Games and Gadgets

Playing cards, Arne Card game, IQ Cards

Magnets - Alnico - Horseshoe

Search Rating: 50%

Also see combined categories:
All Magnets
All Alnico Magnets

General purpose horseshoe magnet

Shafting - Carbon Steel - Keyed

Search Rating: 50%

Also see combined categories:
All Shafting
All Steel Shafting

Keyways are cut full length of each bar. Low carbon steel C1018. Good case hardening properties.

Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00. Unhardened carbon steel. Special order may be available for stainless steel, other diameters, other lengths. Please ask.

Shafting - Unground - Silver Steel

Search Rating: 50%

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

Unhardened silversteel shafting for general purposes. Not suitable for precision bearings until machined to correct tolerances and hardened.

See also drill rod. Drill Rod.

Tools - Nut Driver Set

Search Rating: 50%

Also see combined categories:
All Tools

Lengths shown are based on standard stock but may vary.

Games - Dice and Dice Sets

Search Rating: 49%

Also see combined categories:
All Games and Gadgets

Dice sets and gimmicky dice

Slings - Wire Rope - Permaloc

Search Rating: 49%

For general purpose lifting in environments too rugged for synthetic slings. Tuff-Tag identification on every sling for capacity ratings.

Strip - Soft Metal Packs

Search Rating: 49%

For general hobby applications. This brass strip is annealed soft to make it easier to bend. Brass.

300mm lengths. Not recommended for heavy duty applications. For use with bearings we suggest you use items from the category - Shafting - Ground.

O-Rings - Nitrile Rubber

Search Rating: 49%

Also see combined categories:
All O-Rings

General purpose.

Temperature Range: -30^oC to +90^oC. Nitrile: Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids.

Shafts - Flexible - Panel Mount - Cased

Search Rating: 49%

Also see combined categories:
All Flexible Panel Mount Shaft

See PDF file at bottom of internet page for Performance Data.

Shafts - Flexible - Panel Mount - Open

Search Rating: 49%

Also see combined categories:
All Flexible Panel Mount Shaft

See PDF file at bottom of internet page for Performance Data.

Tools - Wire Working

Search Rating: 49%

Also see combined categories:
All Tools

For general hobby applications. Wire crimping and wire bending tools. Spring winder and spring looping.

Tools - Body and Post Reamers

Search Rating: 49%

Also see combined categories:
All Tools

Body reamers, antenna post reamers

Lengths shown are based on standard stock but may vary.

Bushes - Plastic - Iglidur G - Flanged

Search Rating: 49%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 ^oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Bushes - Plastic - Iglidur G - Unflanged

Search Rating: 49%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 ^oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Pins - Clik - Stainless Steel 316 Grade

Search Rating: 49%

Also see combined categories:
All Clik Lynch Pins

Self locking ring snaps down to hold them securely in place. Easy grip ring for quick removal. Also known as a lynch pin.

Pin is made from carbon steel and heat treated to RA 50-60. Ring is hot drawn spring steel with hardness of RC 47-48. Zinc plated.

Rod - Drill - A-2 Air Hardening

Search Rating: 49%

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Air hardening. Maximum abrasion resistance. 65 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

Rod - Drill - O-1 Oil Hardening

Search Rating: 49%

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

For general toolroom use. Good non-deforming characteristics. Moderate resistance to abrasion. 90 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

Rod - Drill - Oil Hardening - 480 Series

Search Rating: 49%

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

General purpose tool steel with good wear resistance, toughness and machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

Rod - Drill - S-7 Air Hardening

Search Rating: 49%

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Air hardening molybdenum, chromium, shock resisting. High impact strength with moderate wear resistance. 95 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

Rod - Drill - W-1 Water Hardening

Search Rating: 49%

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

High abrasion resistance and high toughness when hardened. 100 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

Pins - Side Thrust - Double Sided - Steel Ball

Search Rating: 49%

Also see combined categories:
All Side Thrust Pins

For holding, clamping and positioning work pieces. Body is black oxide steel.

Steel ball and elasticised spring with black oxide coated steel body.

Pins - Side Thrust - Single Sided - Plastic Ball

Search Rating: 49%

Also see combined categories:
All Side Thrust Pins

For holding, clamping and positioning work pieces. Body is black oxide steel.

Plastic ball and stainless spring with black oxide coated steel body.

Pins - Side Thrust - Single Sided - Stainless Ball

Search Rating: 49%

Also see combined categories:
All Side Thrust Pins

For holding, clamping and positioning work pieces. Body is black oxide steel.

Stainless ball and stainless spring with black oxide coated steel body.

Pins - Side Thrust - Single Sided - Steel Ball

Search Rating: 49%

Also see combined categories:
All Side Thrust Pins

For holding, clamping and positioning work pieces. Body is black oxide steel.

Steel ball and elasticised spring with black oxide coated steel body.

Tool Steel - 496 Oil Hardening - Flat Stock

Search Rating: 49%

General purpose tool steel with good wear resistance, durability and machinability

Dimensionally stable chromium, tungsten and vanadium electric furnace toolsteel can be used for intricate work. Low 787 to 815 ^oC (1450-1500 F) hardening range makes it easy to harden. Fully spheroidised and annealed for uniform carbide size and easy machining. Each piece is individually wrapped and clearly marked with size, analysis and correct hardness and tempering information. Edge squareness 0.003 mm per mm. Finish is 0.0008mm (0.000032 inch).

Rod - Round - Aluminium

Search Rating: 49%

Also see combined categories:
All Metal Rod - Round

For general hobby applications.

NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.

Rod - Round - Brass

Search Rating: 49%

Also see combined categories:
All Metal Rod - Round

For general hobby applications.

NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.

Oil Seals - Nitrile Rubber

Search Rating: 49%

Also see combined categories:
All Oil Seals

DIN 3760 - General purpose grease and oil sealing. Note - metal cased and rubber cased seals may be interchanged at our discretion. If one or the other is specifivally required please let us know when ordering.

Operating Temp. Range: -30^oC to +90^oC. The rubber elastomer outer covering tolerates thermal expansion as well as roughness in the housing bore. Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids.

Rod - Round - Stainless Steel

Search Rating: 48%

Also see combined categories:
All Metal Rod - Round

For general hobby applications.

NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.

Tube - Round - Soft Metal Packs

Search Rating: 48%

Also see combined categories:
All Soft Metal Packs

For general hobby applications. This tube is annealed soft to make it easier to bend. Copper, brass and aluminium,

300mm lengths. Not recommended for heavy duty applications. For use with bearings we suggest you use items from the category - Shafting - Ground.

Lanyards - Nylon

Search Rating: 48%

One piece moulded retainer designed for light duty retention.

Customer assembled loop is designed to be used with press lock rivets or other fasteners. Nylon 6/6 in UV stabilised black.

Rod - Round - Soft Metal Packs

Search Rating: 48%

Also see combined categories:
All Soft Metal Packs

For general hobby applications. This rod is annealed soft to make it easier to bend. Copper, brass and aluminium,

300mm lengths. Not recommended for heavy duty applications. For use with bearings we suggest you use items from the category - Shafting - Ground.

Tube - Round - Aluminium

Search Rating: 48%

Also see combined categories:
All Metal Tube - Round

Hollow round tubing for general hobby applications.

For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.

Tube - Round - Brass

Search Rating: 48%

Also see combined categories:
All Metal Tube - Round

Hollow round tubing for general hobby applications.

For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.

Tube - Round - Copper

Search Rating: 48%

Also see combined categories:
All Metal Tube - Round

Hollow round tubing for general hobby applications.

For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.

Tube - Square - Aluminium

Search Rating: 48%

Also see combined categories:
All Metal Tube - Square

Hollow square tubing for general hobby applications.

Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.

Tube - Square - Brass

Search Rating: 48%

Also see combined categories:
All Metal Tube - Square

Hollow square tubing for general hobby applications.

Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.

Gearboxes - Cross Axis - 47 x 40 x 22mm

Search Rating: 48%

Also see combined categories:
All Cross Axis Gearboxes

Worm and Wormwheel box. 1.4 to 2.5Nm. 5:1 to 120:1 ratios. P20 and PF20.

Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.

Tube - Round - Stainless Steel

Search Rating: 47%

Also see combined categories:
All Metal Tube - Round

Hollow round tubing for general hobby applications.

For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.

Mounts - Leveling - Elastomer Base - OSHA Yellow Steel Cover

Search Rating: 47%

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

Protects general metalworking processes equipment including punch presses, milling machines, lathes, mixers, injection moulding machines, grinders from shock and vibration. Adjusters.

Simplifies installation. 63.5mm of neoprene provides controlled deflections under load. High isolation efficiency for vibration and shock forces, and reduction of transmitted sound. Adjustable up to 12.7mm above loaded height by a few turns of the leveling bolt and tightening the checknut. Corrosion resistant outer housing provides high strength. Neoprene elastomer resists oil, grease, ozone and caustics. Zinc plated hardware resists rust. Hex head bolt and locknut finished with mounts. Height dimensions indicate free height of mount under no load.

Gearboxes - Cross Axis - 110 x 95 x 38mm

Search Rating: 47%

Also see combined categories:
All Cross Axis Gearboxes

Worm and Wormwheel box. 10.3 to 40.0Nm. 5:1 to 120:1 ratios. P45 and PF45 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.

Gearboxes - Cross Axis - 130 x 110 x 46mm

Search Rating: 47%

Also see combined categories:
All Cross Axis Gearboxes

Worm and Wormwheel box. 13.4 to 57.0Nm. 5:1 to 120:1 ratios. P55 and PF55 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.

Gearboxes - Cross Axis - 150 x 125 x 54mm

Search Rating: 47%

Also see combined categories:
All Cross Axis Gearboxes

Worm and Wormwheel box. 30.0 to 118.0Nm. 5:1 to 120:1 ratios. P60 and PF60 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.

Gearboxes - Cross Axis - 90 x 75 x 32mm

Search Rating: 47%

Also see combined categories:
All Cross Axis Gearboxes

Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.

Tape - Silicone Wrap

Search Rating: 47%

Also see combined categories:
All Tape

Self fusing silicone wrapping tape for emergency repairs or general protection. Seals leaks. Permanent. Self Bonding. No adhesive. Supa Tape.

Resists Fuels, Oils, Acid, Solvent, Salt Water, Road Salt and UV Rays. Temp Range minus 50 ^oC to plus 260 deg C. Insulates 8000 Volts (per unstretched layer). Tensile Strength 700psi. Lasts for years with a permanent air tight and water tight seal. Some uses include emergency radiator hose repair, insulation for radioactive areas, garden hose repair, exhaust pipe repair, electrical insulation, tool grips, sporting grips, rope ends, air duct joints, wire bundles. Areas of use include outdoor, auto, marine, workshop, motorcycle, camper, hunting, fishing, farming, plumbing, corrosive areas.

Washers - Nord Lock - 316 Stainless

Search Rating: 47%

Also see combined categories:
All Serrated Locking Washers
All Lock Washers

Supplied in pairs

Steel: Hardness HRA 75+/-3% (HRC48) Passivated Zinc Plated. ALWAYS LUBRICATE FASTENERS BEFORE REUSING. When reusing fasteners the friction is always higher. When tightening, a 20% higher torque should be applied than if tightening against a flat washer. Also see Lockrite and Disc Lock washers.

Washers - Nord Lock - Zinc Plated

Search Rating: 47%

Also see combined categories:
All Serrated Locking Washers
All Lock Washers

Supplied in pairs

Steel: Hardness HRA 75+/-3% (HRC48) Passivated Zinc Plated. ALWAYS LUBRICATE FASTENERS BEFORE REUSING. When reusing fasteners the friction is always higher. When tightening, a 20% higher torque should be applied than if tightening against a flat washer. Also see Lockrite and Disc Lock washers.

Posi Drive Stage - Ball Slide

Search Rating: 43%

Also see combined categories:
All Posi-Drive Stages

Compact economical Posi Drive Stages take the work out of designing linear motion control systems.

These stages require no alignment of components and install with only 4 standard fasteners. Fitted with anti backlash 9.525mm diameter leadscrews with 2.54mm lead and zero backlash multibeam couplings. NEMA 23 motor mounts. Straight line accuracy up to 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm.